Search This Blog

Monday, June 6, 2011

IR LED speed/red light license plate photo blocker

My town installed two red light cameras and a speed camera in a 1/2 mile stretch into my neighborhood.  They lowered the speed limit too.  The week they put up the speed camera I got three tickets for going 42mph and 43mph in a 30mph zone.   That made me all warm and toasty inside.

So I thought I'd play with technology to spoil the photos of license plates and share the fun with the world.
Can't jam the radar but I could theoretically make it harder to get a photo of my plate.  They want to have really clean photos to stand up in court.

OK - so this is totally for fun and i'm not advocating anyone to break any laws or even bend them.
Whatever you do is totally up to you, I bear no responsibility.  If this is illegal where you live, I encourage you not to try it.   This is a playground for technology and not anything else.  Reading further in this blog is acceptance of the fact we are all responsible for our own actions.

I used to build IR cameras for a living, so I know that all digital cameras are sensitive to
near IR radiation.  IR LEDs transmit on wavelengths from 850nm to 1100nm.  These are what are used
for IR remotes, etc.  Invisible to the eye but visible to silicon digital camera sensors.
Visible light is is 390-750nm.  Silicon is used as sensors, and silicon absorbs these wavelengths.



Absorption coefficient of silicon


Some filters can be applied to cameras to filter out this wavelength, to improve the
sensitivity of the camera to visible.  However sharp filters are almost physically impossible
and very expensive, they require many precisely controlled layers of deposition.
These are also used as invisible illuminators for security cameras, so we know cameras see them.

First I will leave them illuminated all the time, rather than try to catch the flash with a photocell some other nonsense.  That is how photographer's flash extenders work, they sense the flash and make another flash fast enough that the shutter is still open, but the sensor is a lot closer and things are much more controlled than the outside environment.  Speed cameras must have a pretty fast shutter speed (I calculated this below) too.  The reaction time would be short, the flash hard to detect.

There are some phone apps to warn you of these cameras, like this one.  Radardroid Lite
Tried them and they are OK, but it didn't have the same "stickin' it to the man" appeal.

Since IR is invisible, this should be legal.   I can't cover the plate, license plate covers are illegal in my state.  The IR LEDs must be on the edge of the plate, close enough that some of the numbers can't be photographed due to the "bloom".  Just a little glare to make it hard to read and the ticket will be blocked.

I had seen that myth busters tried something like this with visible LEDs and claimed it was busted.  But had it worked they wouldn't be able to show it for legal reasons.  I'll try IR LEDs, and I'm going
to amp it up with a bunch of lights.  The glare will be huge I hope.  Daytime light may be too strong, but
what the heck I'll try it anyway. I'm a bit unsure that the lights will be bright enough and this may all be a boondoggle.

One issue will be heat.  I want to run the diodes at as high a current as possible.  I considered flashing
them at a high rate of speed to cool, but that might miss the exposure all together and the average current
wouldn't be any higher.  So I might as well run them off DC to maximze intensity.

There is a possibility that flashing at a high rate might be better to throw off the exposure control
of the camera.   However I don't want to risk the lights being off during the time the photo is
taken, so the flashing will have to be fast.  I considered flashing them in banks, but that wouldn't
have the effect of messing up exposure control.  I think an all on - all off flash would be most disruptive
to photography.  I will have to experiment with what works best.

Speed cameras must have long focal length lenses and short exposure times to get sharp photos
of moving cars from far away.   That's why they need a flash, they need all the light they can get.
I'm guessing they need exposure times of 1/250 to 1/1000 to capture the moving car.
An electric flash is a very fast burst of light (1/1000 of a second or less, sometimes much less)

Flashing the LEDs at 1kHz would mean that 50% of the time I'd miss being on when the
photo was taken.  IR LEDs are designed to modulate at 30-40kHz for remote control.
So modulating at >5KHz will keep the LEDs on for the photo time and will easily be
in the response time of the LEDs.

So I bought 40 IR LED's from Digikey of various wavelengths.  I sorted for the highest
power with reasonable field of view, and of course, low cost!!

I already had 10 IR SFH415 U diodes from the IR sleeper and TV bgone projects.
I also bought these others from digikey, all were less than 50 cents apiece.
I wanted a mix of wavelengths but i especially wanted the 850nm ones, because they
will be closer to visible and will put more energy into the camera.  Maybe I should
have bought all 850nm, but I thought a mix for experimented would be best to start.

11067-1001-NDDIODE IR EMITTER 5MM IR CLR LENS00.48500$4.85
210475-2871-NDEMITTER IR 850NM 5MM RADIAL00.48400$4.84
310475-1458-NDEMITTER IR GAAS 950NM 5MM RADIAL00.31300$3.1
Links
http://search.digikey.com/scripts/DkSearch/dksus.dll?Detail&name=475-1458-ND
http://search.digikey.com/scripts/DkSearch/dksus.dll?Cat=524328&k=67-1001-ND
http://search.digikey.com/scripts/DkSearch/dksus.dll?WT.z_header=search_go&lang=en&site=us&keywords=475-2871-ND&x=9&y=15
http://search.digikey.com/scripts/DkSearch/dksus.dll?WT.z_header=search_go&lang=en&site=us&keywords=475-1458-ND&x=9&y=14

As you can see, they didn't break the bank!  So far I've spend <$20.  The traffic tickets were $40 each.




Here is a sample of what they do to a digital camera when illuminated!
I can't show you what they look like to my eye, but they look dark and off.

I'm going to experiment with illumination, photos and placement when the parts come.

Got a license plate frame, plan is to drill it out and insert the LEDs.  Got black to
make them less obvious.  Got one that had a wide border along the bottom that will
be close to the numbers.  This one has a cheezy "carbon fiber look"  that has a
shiny woven look that will disguise the LEDs a little better.  It is thick plastic and
hopefully will drill.  Here is a photo with it on an old license plate


 

Pilot Automotive WL-714-CF Carbon Fiber Look Car License Plate Frame

http://www.amazon.com/gp/product/B002VKO60C/ref=as_li_qf_sp_asin_il_tl?ie=UTF8&tag=workingsilico-20&linkCode=as2&camp=1789&creative=9325&creativeASIN=B002VKO60C






This was the results of my initial comparisons between the three LED types
IR LED                        wavelength                      comment                        brightness
OED-EL-1L2                     950             clear lens, high view angle              Highest
SFH 4556                          850              glows dull red to the eye               Medium
SFH 415 U                         950              dark and innocuous looking          Medium

Generally, the clear LED was brightest to the digital camera, and the 850nm diode
which should have had a wavelength advantage, wasn't appreciably brighter.
Worse yet, it had some visible wavelength dull red glow.  Not bright, but
it would be visible in the dark and raise suspicion.  Too bad the clear LEDs are
a little more obvious but seem to be the best.


In this photo the LEDs are in order left to right, SFH 4556, SFH 415 U, OED-EL-1L2, SFH 415 U.
You can see the OED-EL-1L2 is the brightest (third from left).  The 850nm diode has no
particular brightness advantage over the 950, which surprised me since it should have several
times the absorption by the camera.  It's visible glow is probably going to kill the use of this one.

OK, for the OED-EL-1L2, the peak current is 1A, but the power dissapation is only 150mW
and the DC current allowed is 100mA.  The forward voltage is 1.2 to 1.6V
http://www.lumex.com/specs/OED-EL-1L2.pdf

That means that I want to shoot for 150mW to put the LEDs at their max light output.
100mA DC times 1.2-1.6V Vforward = 120mW to 160mW.  So I have to keep the average
current to 100mA.   My prototype will power the LEDs from 5V Arduino output but later
I may make a 12V simple circuit to do the oscillation.   5V/100mA is 50 ohms.  But since
I'm flashing at 50% duty cycle, I will need 25 ohm resistor in series.   The above photo was
takin with 100ohms, so I will be twice as bright as that.

Obviously the Arduino can flash an LED at that kind of current.  The TV bgone uses a 2n3904
bipolar to switch the current, without any series resistor.   I also have a pile of 2n7000 mosfets
that will save me some resistors.  They can take 350mA.  This was the tv bgone circuit.  As
you can see it needed two stages to fan out the current drive.  the 2N7000 won't need that
as the gate draws no current.  Everyone should buy a bag of these, for 0.17 for 100.

To avoid a series resistor, I could drive the LED with a low duty cycle high current pulse.
The 2N7000 has a Rds(on) of about 2 ohms at 0.5A.
http://www.st.com/internet/com/TECHNICAL_RESOURCES/TECHNICAL_LITERATURE/DATASHEET/CD00005134.pdf
The LEDs could handle 1 amp peak (remember from above).   5V - 1.5V (Vforward) = 3.5V across the transistor.  3.5V/2 ohms = 1.75A.  Too high for the LED without any series resistance. But if I put two LEDs in parallel, I will split that current and be at 0.875A per LED.  This is not a perfect solution because the
LEDs may have slightly different forward voltages, and will not share the current equally.  But best I can do.

Now I have to keep the LEDs from dissipating more than 150mW on average.
0.875A * 1.5V = 1.31 W peak.   150mW/1.31W =11.5% duty cycle.

SoI could flash LEDs at 10kHz, with 11.5% duty cycle, two LEDs per 2N7000 transistor, no series resistors.   5V supply.

To save components, I could bring the duty cycle up to 50%, and load on more LEDs in parallel.
I could put 10 LEDs on at 50% duty cycle, 0.50 * 1.75A * 1.5V / 10 = 131mW per LED.

I'm in trouble on the 2N7000s.  they only want 1.4A peak current, and I'm doing 1.75A.
Thought I'd run it anyway, if I blow one they are cheap.  However it gets scary hot and the
LEDs don't at all.  I think I will switch out the 2N7000 with a FQP50N06L monster.
These cost a over a buck a piece but they are 50A rated.
Problem is they have a really low Rds(on) = 0.2 ohms.  So my current calculations are
out the window and i need to introduce a 2 ohm resistor.  Arrgh.

OK.  Rethink time.  Is flashing really better than DC?  Time to experiment because flashing
is going to take many more components.  DC will take a couple resistors, while flashing will
require an oscillator, switching transistor, etc. 

I set up an experiment flashed, side by side with DC.   The flashed had 50% duty cycle with
half the series resistance.  100ohms for flashed, 200 ohms for DC.  The DC was noticeably 
brighter to the camera.  OK. DC wins for complexity and effectiveness.  

The lower 5  LEDs are the DC, the upper 5 are switched at 10KHz.

I mocked up an array of LEDs and resistors and plugged it into 12V for one last full
scale test before building up the license plate final version, and got a surprise.




While this was on, it started to smell hot.   The resistors were getting really warm.  Doh! I have 1/2W 100 ohm resistors, so that I put (12V-1.5V)/100ohms=105mA through the LEDs, their max rating.  However since I'm running from the 12V auto supply directly,  that puts 10.5V * 1.5mA = 1.1W through the resistors.  Before I had been running off 5V during tests and the resistors did not get so hot.  This simpleton project is becoming more complicated because I'm trying to make a cheap solution.

OK, brain finally started functioning.   Many LEDs will be in series with a resistor
to set the current, this will prevent dissipating too much power in the resistor
and generally be more efficient, fewer components, all good.
6 LEDs in series like christmas lights, 6*1.5V=9V.   12-9V=3V across the resistor.
100mA*3V=300mW, which is in spec for the 1/2 watt (500mW) resistors.  Might even
be able to squeeze in a 7th LED.    3V/100mA= 30 ohm series resistor.


Tested out strings of 6 LEDs in series with 30 ohms.  Gets nice and bright, doesn't get hot, doesn't waste power. 

OK, here is the complete circuit drawn up.  Strings of 6 LEDs will be used.


I think I can pack the LEDs in and solder them into chains.  So the big structure at the bottom will look like two rows of alternating staggered LEDs with no interruption in the middle for the ground.

There will be a tight cluster in the bottom center of the plate, and a smaller cluster at each side which is nice and close to the numbers.

Drilled a hole in the license plate frame as a test (see link above) and it drilled pretty well, nice clean hole.
The challenge is going to be making nice neat regularly spaced holes or the whole thing will look amateur.
I put one of the clear IR LEDs that won the brightness test, but it looks really obvious in the frame.  Maybe somebody with a tricked out car might not care, but it really looks like a light, even when it is off.  The solid color SFH 415 U look far better and less suspicious.  I'm going to have to use those, i'd never have the nerve to put the others on the car.  Forget the nice shiny OED-EL-1l2s.

Hard to get a good photo to show what i mean, but here it is...


Obvious Clear LED (shown off, which is how it looks to the eye).  I thought the pattern would hide it.

Nearly invisible black IR LED.  It is a bump of course and the picture isn't great.  But you get the point.

I was planning to use my CNC machine that I've been writing about to drill the holes.  Sorry if not everyone who reads these happens to have one.   However the CNC machine stage is small enough I'd have to do the job in three passes, and I got impatient with the setup and just did it on the drill press.  I clamped a bar to the press stage to make all the holes even distance from the edge of the frame, but freehanded the spacing.  I was eager to move this project along and get to some outside trials.   I did OK but not great in spacing the holes and kinda goofed on getting the placement of the arrays even on both sides.  No harm done but a production version would have to be neater.  The plastic license plate frame drilled nicely though, it was a good choice for the project.


Here is a picture of the holes I drilled.  I put the LEDs in clusters to make hot spots in the photo, rather than in a whole line around the plate.  The thought is that unevenness and tight hot spots will be best to ruin the photo.

Next to glue in the LEDs and wire them up!  A note about LEDs since a few non EEs seem to be reading this post.  LEDs aren't light bulbs.  They have a polarity and must be hooked up the right way or they don't light up.   This is how you tell which way to put them in.  Note that not ever LED follows the long lead convention, but the flat side is a reliable indicator of polarity.



Here is a shot of the LEDs getting glued into the main phaser bank in the middle.  Remember that they are in strings of six, so the pattern of anode and cathode is important to be able to easily solder them into strings.  I will show the pattern later.  This is about the best I've been able to capture the look of the LEDs in the frame. They are hard to see.



Daisy chained LEDs soldered up to 30 ohm resistors.  Glued in the LEDs and bent the leads and soldered them together into chains of six.  Make sure to keep the polarity correct in the chains.  A little messy but this is a prototype. 


Here is the finished main LED array (sorry about the 90 degree photo).    Power is off in this photo so you can see how it looks to the eye


For now I'm wiring these into the license plate light power.  They will only be on when the lights are on.  Using trailer light power taps.  Pico 1560D 18-14 AWG (Blue) Electrical Wiring Hot Line Quick Splice / Tap-In 5 Per Package


OK moment of truth.  Did it work??  Eh maybe....

So a lot depends on the lighting.  Taking a photo of a moving car and reading the license plate is not easy.  A speed camera needs a lot of light, a high speed lens, a short exposure time.  So it shouldn't take much to spoil the photo.    This photo was taken with indoor lighting and no flash.   The picture is very messed up, lots of glare but all in all you can still read the plate if you try.  It might not meet the standard of quality to hold up to get you a ticket though.  Of course you don't want to mess up the photo just enough to have them wonder what you are up to.   You can read my plate here, but eagle eyes will reveal this is just an old expired plate I'm using as a photo model.


This time I used the flash.  The IR LEDs are a nice decorative touch, but pretty much useless.  However I'm 3 feet away shooting a plate that isn't moving.  A real photo won't be this good.  Anybody's TV remote in the neighborhood would be probably be totally jammed :-)

I went out on a fairly sunny day and put it on the car.  Stylin' huh?   All in all I succeeded in making something that is not going to draw any attention under normal circumstances.


Powered it up with a battery charger to start.  This later proved to be a slight issue.  Can you read the plate?  I can.  Is it even on??  It was so bright outside I couldn't see the display on my camera.  This is a tough test.  It was bright and sunny.  The car was not moving of course, but I also didn't have a professional camera.  if you see below, it might be better than this photo showed because of the power supply I was using.


Here is a closeup like what you get in the mail when you run a camera.  Still looks like a FAIL.   The LEDs are pretty but noneffective under these lighting conditions.  Notice something strange happened, which may have reduced the brightness.  The LEDs were powered from a battery charger in this picture, and it has a lousy AC to DC rectifier that is probably flashing the lights at 60Hz.  When there is this much light, the camera is taking an exposure shorter than the time it takes to read out the camera's photo array (I told you I used to design IR digital cameras for a living, trust me).  As a result the picture changes while it is being taken, and the 60Hz is not integrated and the LEDs appear to be on in different patterns every time you take a photo.  That won't happen with the car's DC power, so it might be twice this bright when hooked into the car power.  That is why it looks like some of the LEDs are not working.  But anyhow there is zero glare.


So here is my conclusion for now.   There is hope that this would work when it's dark, rainy, or otherwise non ideal for photo taking.  On a sunny day, drive slowly.   Or make the LEDs spell out a message like "I love the police".   I'm not going to go out and run a camera on purpose, so there is no way to know if this is going to work even on a dark night.

Next.... Ramping it up!

What went wrong?  I had the design parameters turned too far for innocuous, stylish and low cost.  I need to redo the project and focus on brightness and high power and see if I achieve something that works first.
The clear LEDs were 50% brighter in my early tests, but I chickened out from using them.   I went for cheap LEDs and simple circuits.  Since then I've seen light up license plate frames for sale so I think the lights could be more obvious without attracting attention.

I'm starting a new post for the next version, click here: http://blog.workingsi.com/2011/06/improved-high-power-ir-led-speedred.html

Some other notes for other ways to do this project...
Later I saw someone driving down the road with this:
So if you wanted you could buy one of these, already has the power connections, and replace the glowing eyes with 850nm high power LEDs.  This is not my style, but if it is yours it is an easy way to beat the camera.  The 850nm LEDs would glow and look like it did before, and be totally undetectable.  Not enough room for all the LEDs I'm using, but could give you a little help.

A little googling found this too.  So this could serve as a starting point for a mod, replacing the LEDs with IRLEDs and keeping low profile.

You could also get one of these, and ramp up the power.  This alone has 140 LEDs, but I don't know what type so there is no way to know if you could achieve enough brightness.




43 comments:

  1. Yeah, possible minor problem, if a police car has video for evidence then surely the office in the car will notice the glare on their screen and work it out?

    ReplyDelete
  2. LEDs that only switch on over 30mph might be worth it even if it adds a lot to the complexity.

    ReplyDelete
  3. Hadn't thought of the police video camera in the cruiser getting messed up, could be an embarrassing problem. I like the speed sensitive idea, that could keep you out of trouble when obviously you don't need it. (Except for red light cameras, but it is the speed cameras that I care about)

    ReplyDelete
  4. I thought about flash back designs, but the speed cameras in my area don't seem to have a detectable flash. I never saw it go when I got a ticket. A flashback has the advantage that the power could be boosted for a short time without overheating the LEDs and make it more effective. The GPS is nice idea, I already have an app now that can warn you when you are near a camera. I might use that!

    ReplyDelete
  5. EBay has 5 Watt IR LEDs for about $15 it shouldn't take much more than 1-2 to saturate at least part of the image

    ReplyDelete
  6. I use these 850 nm LEDs for my microscopy instruments. They are not cheap, but very reliable.

    http://www.roithner-laser.com/datasheets/led_single/elj/elj-850-629.pdf

    ReplyDelete
  7. why not just have an on off switch? turn it on when you are driving normal, cop is around, turn it off.
    Simple, convenient and easy.

    ReplyDelete
  8. Late comment but put hight powered ones on the overhang in the trunk lid shining on the plate. Set them up like mini headlamps shining down on the plate itself and switch them on and off when needed.

    Put them near where the current plate lights are. No one would think to look up there anyway so there is natural camouflage...

    ReplyDelete
  9. keep it up! down with the money takers,I am trying my own and will share if I hit on something,and I heard the Law states that a plate has to be visible and be readable.Nothing saying it has to be able to be Photoed or Video.

    ReplyDelete
  10. What about the screw in led colored lights that screw into the holes that hold the plates onto the car replace them with the high powered leds and have a switch to turn on or off. this is what i am hoping will work on my motorcycle any tips would be appreciated. The plate is small so i am hoping they are bright enuf w just 2

    ReplyDelete
  11. How about a LCD cover that was segmented in one inch squares. Each square oscillates opaque to transparent @100hz in a random pattern. So that only 20% of the plate is visible at any time. To the eye it would appear tinted but the camera would only see 20% of the plate.

    ReplyDelete
  12. I did a post on that idea a long time ago. You could use an old laptop LCD display and remove the backing. Seems a bit fragile and never built it.

    ReplyDelete
    Replies
    1. The tech used in auto darkening welding helmets may be tough enough and operates at frequencies suitable for this project.

      Delete
  13. You are over complicating the project, if the cameras in your area have a flash, just buy a can of Rustoleum reflective clear paint. Then spraya a light coating of the glass bead paint over the entire plate. Then the cameras own flash will glare the plate its self. Well at least at night.

    ReplyDelete
    Replies
    1. definitely this. not sure if this works with tolls, but SWIM used reflective spray for years and never got red lighy tickets. Need to pick up another can and test, I am surrounded by toll roads that would actually be worth the cost of admission if not for the fact that they get just as jammed up as regular highways during crunch time.

      really like the effort here though, big respect. I just think this would be bad news if pulled over and found, which is not a risk I'd be willing to take.

      Delete
  14. Hey, nice blog. I know it is kinda old but was a fun read.
    Also, FYI, the first image is broken because you have an extra 'i' in 'Appendicies'...it should be 'Appendices'.

    ReplyDelete
  15. Thanks. Fixed the link. They must have fixed their typo and broken my link :)

    ReplyDelete
  16. I realize this is an older post, but it's obvious you keep up with it, so wanted to say thanks for being so thorough and detailed. I'm not an EE, but could follow your steps easy enough. Well put, thanks for taking the time. I would like to try a similar project, but work to aim the lights at the plate and let the ir wash out "bathe" the plate in bright pockets of ir light. Are you still pursuing this, or have you moved on entirely?

    ReplyDelete
  17. Got bored and moved on after a couple more generations... can't help the ADD. Speed cameras have gotten trickier too, lots of different types of flashes.

    ReplyDelete
  18. The real danger of this technology is the license plate readers that accumulates the comings and goings of every citizen criminal or not. This information would be valuable to a police state. In a police state all citizens are considered suspect and guilty until proven innocent and even innocence wouldn't matter in a police state if the government is so corrupt.

    ReplyDelete
  19. Did you say... "if the government is so corrupt" ???

    ReplyDelete
  20. Any updates guys .... this project could turn into a million dollar idea ... people all around the globe would buy one of these if it works ...

    ReplyDelete
  21. watch for a version of this on ghostplate.com
    In the testing phase now, production slated for August 2016 release.

    ReplyDelete
  22. This comment has been removed by the author.

    ReplyDelete
  23. Superb Post!!!! I have read this post very carefully and got informative points. Thanks for such a helpful post. Keep Sharing........
    https://goo.gl/5ULwve"

    ReplyDelete
  24. This comment has been removed by the author.

    ReplyDelete
  25. At the point when a given video picture is provided to the PC program which controls the LED screen, these LEDs are quickly lit and stifled in an exact grouping to make the required pictures.led displays

    ReplyDelete
  26. Awesome things you've generally imparted to us. Simply continue written work this sort of posts.The time which was squandered in going for educational cost now it can be utilized for studies.Thanks Author KRM

    ReplyDelete
  27. Pretty good post. I just stumbled upon your blog and wanted to say that I have really enjoyed reading your blog posts. Any way I'll be subscribing to your feed and I hope you post again soon. Big thanks for the useful info. 2000 lumen led bulb

    ReplyDelete
  28. I got this to work but I did it a little different. You need to direct the 850-950nm light to go through a high polished plexiglass cover that goes over the plate. Not just a frame. You need to have it on at all times. You drill the edges of the plexiglass with a hole just large enough to stick the head of the LED in it. However, as I stated, you have to polish the insides of every hole. You put the leds in and use clear crazy glue gel to hold them in. Yout put in as many as you can around the outside edges then build a frame to hide the wires. When on the IR light will travel the path of least resistance which just so happens to be the clear area of the plexiglass that's over the plate. With only the holes being polished to a crystal clear and LED's in them stopping the light from emitting and the edges that are not holding LED's (like the space from 1 LED to the next LED) should remain in rough unpolished condition. It sort of works like a self contained fiber-optic window that covers your plate where the high intensity light from the LED's is mostly right over your plate blocking the camera. I built this back in 2010-2011 and it works. The ghostplate stuff doesn't work for crap. Lots of people complaining about that. PLDC doesn't give a great result for traffic cams. If you build this the plate will look exactly like looking into a highbeam of an airplane landing light (to the traffic cam that is, and it makes no difference at day or night, always works). My job here is done!

    ReplyDelete
  29. If infrared cameras are heat sensitive, why not just put a 12volt heating element behind the license plate that stays on when engine is running (off when engine not running so as to not drain battery), heats plate (not hot enough to melt bumper or other mounting surface), defeats IR camera. Done!

    ReplyDelete
  30. Thank you for writing a great blog. Nowadays, focus light for showroom and good quality LED lights are available in the market at normal prices. Go to jainsons lights showroom today and buy good LED lights at Affordabe price.

    ReplyDelete
  31. No doubt this is an excellent post I got a lot of knowledge after reading good luck. Theme of blog is excellent there is almost everything to read, Brilliant post. flexible track lighting

    ReplyDelete
  32. How about using high power IR led illuminators available nowadays in Amazon etc? They aren't really that expensive, available in 750/850/950nm and having one right below or top the plate could work, car structure permitting. 60W lightbar seems to be around 200 US$. Here, where I live, we have very dear speeding tickets, just got 170 € ticket for 11 km/h overspeed (that's 190 US$ for 7 mph speeding on level straight road! Nothing to do with safety).

    Commercial IR illuminator has of course "legal" purposes like driving in dark ;)

    ReplyDelete
  33. It is truly a well-researched content and excellent wording. I got so engaged in this material that I couldn’t wait reading. I am impressed with your work and skill. Thanks. photos alimentaires

    ReplyDelete
  34. Thank you again for all the knowledge you distribute,Good post. I was very interested in the article, it's quite inspiring I should admit. I like visiting you site since I always come across interesting articles like this one.Great Job, I greatly appreciate that.Do Keep sharing! Regards, best led work lights new

    ReplyDelete
  35. Best LED Grow light
    Pretty good post. I just stumbled upon your blog and wanted to say that I have really enjoyed reading your blog posts. Any way I'll be subscribing to your feed and I hope you post again soon. Big thanks for the useful info.

    ReplyDelete
  36. This comment has been removed by the author.

    ReplyDelete
  37. Tiras de luces LED al por mayor, Neon LED Flex y Custom Neon Sign, también pueden proporcionar soluciones profesionales de luces LED inteligentes. Tira LED de corriente constante

    ReplyDelete